Small capacity, low gravity center, lightweight, portable. High magnetism magnet increases dependability of operating and draft load to assure the machine operates smoothly. It can operate many machines on the base of increase dependability of operating and self-stop function. The guide transfer switch can make it move toward right/left.Guide equipment is screw lockage-on type. Guide wheel’s height can be modified by three methods. New spacing switch system increases the limited height of distance plate.All of the top characters are wonderful on the aspect of “effective welding” and “operated by primary person”.
1) Adjusting gliding block of torch: You can use this equipment to adjust arc starting point toward up/down, front/rear. Each distance of run is 45mm.
2) Locking equipment of torch: You must make sure the torch is locked when you assemble it.
3) Control wheel and control wheel’s arm.
4) Self-stop switch
5) Operating panel( illustration in full in after chapters)
6) Torch
7) Metal plug: This plug is external plug. The cable is used to connect trolley with feeder and provide power for them.
(There are two branches, one connecting feeder and another connecting power.)
5) Propelling wheel
6) Regulating spindle of the torch: Release the screw and you can adjust the angle of the welding torch. (40~55°).
10) Lifting hand grip
11) Magnetron hand grip: The pick-up of magnet is controlled by this hand grip, such as diagram 3: up is declutching and down is combining.
1) Power indicated lamp: When the power is on, the lamp is light.
2) Speed control knob: Increase speed when you revolute clockwise, decrease speed when revolute anti-clockwise.
Speed scale matches following speed chart: Adjust the welding speed according to welding specifications.
scale |
speed(mm/min) |
|
scale |
speed(mm/min) |
3 |
200 |
9 |
970 |
|
4 |
330 |
10 |
1080 |
|
5 |
460 |
11 |
1180 |
|
6 |
590 |
12 |
1280 |
|
7 |
720 |
13 |
1380 |
|
8 |
850 |
|
14 |
1480 |
3) Stop button:Press down the button and the trolley stop walking. The selector switch can control whether the welding stops.
4) Walking guide and power switch: The switch is used to control welding guide and power.
5) Start button:Press down the button and the trolley begin to walk. The selector switch can control whether welding begins at the same time.
6) Model select switch---there are three positions. The individual function is :
TEST:On this position, the feeder works. You can control arc starting/ retracting arc by your hands, then reset after release.
ARC ON:On this position, the normal welding begins. If you press down firing switch, the trolley starts to walk at the time of arc starting.
NEUT:On this position, if you press down start button, the trolley walks but the welding doesn’t start.
Specifications
1.Weight |
6.9 Kg |
2.Driving method |
Four rubber rims driving |
3.Hauling power |
16 Kg |
4.Running speed |
150~~1500 (mm/min) |
5.Tracking mode |
Guide wheel type |
6.Height of torch |
Three chooses |
7.Adjusting scope of torch |
Horizontal angle: 40°~55° Up /down moving: 45mm Front/rear moving: 45mm |
8.Torch |
Bended welding torch or straight welding torch |
9.Locked equipment of torch |
Suit for bended welding torch or straight welding torch |
10.Needed welding length |
Front-end:127mm; end:127mm |
11.Self-stop function |
By spacing parts of front-end and after end. |
12.Size(length*width*height) |
260x260x264 |
Layout
1) body 1set
2) control wire 1set
3) special torch(fitting parts) (purchase)
4) fuse(1A) 1pc
5) hexangular screw(M5/M6) each 1set
6) manual 1pc
7)certificate of qualification 1pc
8) maintenance bill 1pc